Walchem WebMaster Manuel d'instructions Page 61
- Page / 180
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
57
The relay input assignment choices will be any digital or optional analog inputs that are defined as
a flow meter input.
If the relay control mode is any of the Biocide Timer Based Feed options:
The relay input assignment is Not Applicable.
If the relay control mode is Feed with Another Relay, Feed After Another Relay (%) or Feed After
Another Relay (Fixed Time):
The relay input assignment choices will be all the other relays.
If the relay control mode is Feed as % Time or Dispersant:
The relay input assignment is Not Applicable.
If the relay control mode is any of the Spike modes:
The relay input assignment choices will be all sensors and analog inputs.
If the relay control mode is Alarm:
The relay input assignment is Not Applicable.
If the relay control mode is Activate on a DI:
The relay input assignment will be any Interlock or Generic Input digital inputs.
Analog Output Input Assignment (1 – 4)
This section will only appear if there are one or more 4-20 mA output cards installed.
Use the pull-downs to select the input signal that will be retransmitted as a 4-20 mA output signal.
The possible choices include any sensor input, any sensor temperature signal, or any 4-20 mA
input signal (only applicable if the analog input card is installed).
LCD Display Setup
Up to five parameters may be presented on the front panel LCD display. Click on the radio buttons
next to the parameters to show.
6.3 System Summary Menu
There are no programmable parameters in the System Summary Menu page. Several tables will be
displayed, with information on sensor readings, analog input readings, digital input states, alarms,
relay state, etc.
- Water Treatment Controller 1
- Instruction Manual 1
- TABLE OF CONTENTS 3
- 1.0 INTRODUCTION 5
- 2.0 SPECIFICATIONS 5
- Digital: USB 6
- Ethernet, 10 Base T 6
- Data Logging Menu 13
- 1/8 inch dia 16
- 3/16 inch dia 16
- 1/4 inch dia 16
- 5/16 inch dia 16
- 1/2" 150 PSI 17
- 1/2" 300 PSI 17
- 3/4" 150 PSI 17
- 3/4" 300 PSI 17
- 3.4 Icon Definitions 18
- Intermittent Sampling 20
- Continuous Sampling 21
- Hardwired Options 23
- Prewired Option 23
- IN+ +v IN- IN+ IN+IN-+v +v 24
- IN-IN-IN 24
- IN+IN+IN+ 24
- AC POWER 25
- sensors 2-4 26
- - PLC + 29
- GND +24 29
- 4.0 FUNCTION OVERVIEW 31
- Hard coded Fixed 34
- IP Address: 34
- 199.199.199.2 34
- Web Browser 34
- (Client) 34
- Embedded 35
- Web Server 35
- Fixed IP 38
- Address User 38
- Assigned 38
- 4.7 Startup 40
- 4.8 Shut Down 40
- 5.1 Input Summary 40
- 5.2 Indices 41
- 5.3 Output Summary 41
- 5.4 Alarms 41
- 5.5 Calibration 41
- Temperature Calibration 43
- ORP Calibration 44
- Calibrate 4 mA 46
- 5.6 Relay Control (HOA) 48
- 5.7 Set Points 48
- Relay 1- 8 Set Points 49
- 5.8 Communication 52
- 5.9 Access Codes 54
- 5.10 Software Upgrade 54
- 5.11 Copy to USB Disk 54
- 6.0 OPERATION – Using PC 55
- Controller Date Format 57
- Sensors 1-4 57
- Digital Inputs 57
- Relay (1 – 8) Control Mode 58
- 4-20 mA Inputs 1 - 8 58
- LCD Display Setup 61
- 6.3 System Summary Menu 61
- . The averaged reading 64
- Primary Sensor Assignment 66
- Current Reading/Calibrate 70
- . The averaged reading is 77
- Relay Control Mode 96
- Relay Input Assignment 96
- Current Reading 96
- Output Mode 118
- Hand Time Limit 118
- Event Log 118
- Power-up Alarm Delay Time 122
- Mutual Interlocks 122
- Output Time Limit 122
- Select items to log 142
- Suppresses Datalogging 142
- Triggers Datalogging 142
- Log Files 142
- Scenario 1: 143
- Scenario 2: 143
- Scenario 3: 143
- Ethernet (LAN) 145
- Email To Addresses 145
- ASMTP Settings 146
- Communications Status 146
- Activations 148
- 6.47 Advanced Comms 149
- Network Settings 149
- Import UCF 151
- 6.49 Notepad 151
- 6.50 Access Codes 151
- 6.52 Sub-Network 152
- 7.0 MAINTENANCE 153
- 7.6 Replacing the Fuses 157
- 8.0 TROUBLESHOOTING 158
- ORP Calibration Failure 159
- Output Time Out 161
- Conductivity High Alarm 162
- Conductivity Low Alarm 162
- ORP High Alarm 165
- ORP Low Alarm 166
- 4-20 mA Input Low Alarm 169
- Conductivity Sensor Error 169
- ORP Sensor Error 170
- Temperature Sensor Error 171
- Total Alarm Limit 171
- 8.3 CONNECTION PROBLEMS 177
- 9.0 SERVICE POLICY 178
Produits connexes et manuels pour Mise en réseau Walchem WebMaster
(6 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.911 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels